Book file PDF easily for everyone and every device.
You can download and read online AWWA C214-14 Tape Coatings for Steel Water Pipe file PDF Book only if you are registered here.
And also you can download or read online all Book PDF file that related with AWWA C214-14 Tape Coatings for Steel Water Pipe book.
Happy reading AWWA C214-14 Tape Coatings for Steel Water Pipe Bookeveryone.
Download file Free Book PDF AWWA C214-14 Tape Coatings for Steel Water Pipe at Complete PDF Library.
This Book have some digital formats such us :paperbook, ebook, kindle, epub, fb2 and another formats.
Here is The CompletePDF Book Library.
It's free to register here to get Book file PDF AWWA C214-14 Tape Coatings for Steel Water Pipe Pocket Guide.
Awwa C Tape Coatings for Steel Water Pipe [Not Available] on Amazon. com. *FREE* shipping on qualifying offers. This standard covers the materials.
Table of contents
- Polyolefin Cold Pipe Coating Materials Water Pipe Wrap Tape C214 Standard Images
- AWWA Standards 2016 - American Water Works Association
- SEND AN E-MAIL
- Download Awwa C214 14 Tape Coatings For Steel Water Pipe 2014
- Polyken Tape Coating For Protection Of Straight Steel Pipe
Seja o primeiro a comentar este produto. AWWA Standards Set contains all current AWWA standards more than , plus a one-year subscription that brings you all revised and new standards published during the following 12 months standards.
You have the option to renew your subscription each year. AWWA Standards describe minimum requirements for design, installation, performance, and manufacturing of products used in the drinking water industry. AWWA Standards cover water pipe, treatment chemicals, storage facilities, valves, appurtenances, and utility management practices. Regularly updated to reflect changes in materials, manufacturing, engineering design, and usage, AWWA Standards are consensus documents and prescribe recommended best practices.
The AWWA Standards set includes seven heavy-duty, post-type binders, and plastic-laminated index tabs to organize your standards.
Through 72 In. Through In. Through 48 In. Sec, 5. Adhesion to prepared steel. Water absorption 24 h. Water-vapor transmission. Dielectric strength.
Polyolefin Cold Pipe Coating Materials Water Pipe Wrap Tape C214 Standard Images
Insulation resistance. Tensile strength. Nonpolyolefinic Material Percent by Weight. The manufacturer shall certify that the backing material shall be polyolefin only containing not more than 7.
AWWA Standards 2016 - American Water Works Association
The intermediate -layer shall be compatible with the inner-layer tape and the outer-layer tape shall be compatible with the intermediate-layer tape. The primary function of the intermediate - layer tape is to provide mechanical protection to the inner-layer tape and of outer-layer tape to provide mechanical and outdoor weathering UV protection to the tape system, and secondarily, to contribute to the overall corrosion-protection properties of the system.
The outer-layer tape backing shall be compounded so that it will be resistant to outdoor weathering. To distinguish the intermediate- layer tape from outer-layer tape the colors of the two layers shall be different. The intermediate- layer tape color shall be grey and the outer-layer tape color shall be white.
SEND AN E-MAIL
The outer-layer tape should be of suitable quality for the local environment, as follows:. Nominal thickness 30mil 0. Adhesion to Inner layer.
- awwa c steel water 3 layer - GREET STEEL!
- American Water Works Association.
- pipe coating materials for steel meet awwa c 214.
- Business Law in the Global Marketplace!
- Recent Freshwater Ostracods of the World: Crustacea, Ostracoda, Podocopida;
- Product Detail.
Dielectric Strength. The installed coating system thickness shall not be less than 80 mils 2mm and shall comprise of the following. The properties of the complete coating system shall conform to the following requirements. Sec 5. Four steps, which shall be performed consecutively, shall consist of 1 liquid adhesive application; 2 application of the inner-layer tape directly onto the prepared pipe surface; and 3 application of the intermediate-layer tape directly on top of the inner-layer tape and 4 application of outer-layer tape directly on top of the intermediate-layer tape.
Bare pipe shall be free from mud, mill scale, mill lacquer, wax, coal tar, asphalt, oil, grease, or any other foreign material. Before blast cleaning, surfaces shall be inspected and pre-cleaned according to SSPC-SP 1 to remove oil, grease, and loosely adhering deposits. Visible oil and grease spots shall be removed using a solvent.
Only solvents that do not leave a residue shall be used. Preheating to remove oil, grease, and mill scale may be used provided that all pipe is preheated in a uniform manner to avoid distortion. For consistent surface finish, a stabilized working mix shall be maintained in abrasive recycling blasting machines by frequent small additions of new grit, shot infrequent large editions shall be avoided.
The abrasive working mix, abrasive recycling blasting machines shall be maintained clean of contaminants by continuous effective operation of blasting machine scalping and air-wash separators. The cleaned exterior pipe surface shall be in inspected for adequate surface preparation.
Surface imperfections, such as slivers, scabs, burrs, weld spatter, and gouges, shall be removed by hand filing or grinding if necessary to prevent holidays. Blast-cleaned pipe surfaces shall be protected from conditions of high humidity, rainfall, or surface moisture. No pipe shall be allowed to flash rust before coating. The liquid adhesive shall be applied in a uniform thin film at the coverage rate recommended by the manufacturer.
The liquid adhesive shall be thoroughly and continuously mixed and agitated during application to prevent settling. The liquid adhesive shall be applied to the entire exterior surface of the pipe by spray to cover the entire exterior surface of the pipe. The liquid adhesive coat shall be uniform and free from floods, runs, sags, drips, or bare spots.http://nttsystem.xsrv.jp/libraries/64/pyka-app-zur-kontrolle.php
Download Awwa C214 14 Tape Coatings For Steel Water Pipe 2014
The liquid-adhesive-coated pipe surface shall be free of any foreign substances, such as sand, grease, oil, grit, rust particles, or dirt. Before applying the inner-layer tape, the liquid adhesive layer shall be allowed to touch dry in accordance with the manufacturer's recommendation. The inner-layer tape shall be applied directly onto the prepared pipe surface using mechanical constant-tension coating equipment. The inner layer tape shall be spirally applied with neck down tension as recommended by manufacturer. When applied to spirally welded pipe, the direction of the tape spiral shall be generally parallel to the weld spiral.
The minimum overlap shall not be less than 25 mm. When a new roll of tape is started, the ends shall be overlapped at least mm measured circumferentially. Application of Intermediate-layer tape:. The intermediate-layer tape shall be applied over the inner-layer tape using the same type of mechanical equipment used to apply the inner-layer tape.
Polyken Tape Coating For Protection Of Straight Steel Pipe
The intermediate- layer tape shall be spirally applied with neck down tension as recommended by manufacturer. The overlap of the intermediate -layer tape shall not coincide with the overlap of the inner-layer tape. The outer-layer tape shall be applied over the intermediate-layer tape using the same type of mechanical equipment used to apply the inner and intermediate layer tapes. The outer layer tape shall be spirally applied with neck down tension as recommended by manufacturer.
The overlap of the outer-layer tape shall not coincide with the overlap of the intermediate-layer tape. Pipe Coating System.